[Help]: Cant access webUI #511
Replies: 7 comments 8 replies
-
|
Could you provide the actual run command or compose file you're using? How are you assigning this IP address you mentioned, |
Beta Was this translation helpful? Give feedback.
-
|
Im using the unraid instal via the app store, so theres no compose file per say, or I dont know where to get it |
Beta Was this translation helpful? Give feedback.
-
|
I think I got it |
Beta Was this translation helpful? Give feedback.
-
|
After diggin up a little more, this issue only occures when I VPN in into my unraid server via Tailscale. |
Beta Was this translation helpful? Give feedback.
-
|
Are the other containers you're running also using this If you can show your network interfaces somehow when attached to tailscale and maybe get the output of |
Beta Was this translation helpful? Give feedback.
-
|
Yeah all my other containers are on "abomy-server" network that is 172.18.0.0/24 Tailscale is 100.XXX.XXX.XXX |
Beta Was this translation helpful? Give feedback.
-
|
Any tailscale configuration that you can share? I am not a tailscale user but I am wonder if it is routing traffic across the tailscale VPN that is destined for your software controller, essentially black holing the traffic off to a network where it won't respond. The fact that it only stops working with the VPN points me in the direction of figuring out what is going on. If you're able to share your routing table when connected and when not connected, that might help as well. Use |
Beta Was this translation helpful? Give feedback.
-
|
[image: image.png]
[image: image.png][image: image.png]
This helps?
Matt Bentley ***@***.***> escreveu (terça, 17/12/2024 à(s)
12:34):
… Any tailscale configuration that you can share? I am not a tailscale user
but I am wonder if it is routing traffic across the tailscale VPN that is
destined for your software controller, essentially black holing the traffic
off to a network where it won't respond. The fact that it only stops
working with the VPN points me in the direction of figuring out what is
going on.
If you're able to share your routing table when connected and when not
connected, that might help as well. Use sudo route -n to show the routes.
—
Reply to this email directly, view it on GitHub
<#511 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADFQBZ6YJRZF6IXGORZBOR32GAK43AVCNFSM6AAAAABTWBFTMCVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCNJZGI3TENY>
.
You are receiving this because you authored the thread.Message ID:
<mbentley/docker-omada-controller/repo-discussions/511/comments/11592727@
github.com>
|
Beta Was this translation helpful? Give feedback.
-
|
|
Beta Was this translation helpful? Give feedback.
-
|
So is that the output of your routes when Tailscale is connected? What happens if you turn off Tailscale, disable the subnet route setting for your subnet and reconnect. Are you able to connect to your controller then with the subnet unchecked? |
Beta Was this translation helpful? Give feedback.
-
|
If I disable the route I still can't connect outside of Lan (obviously)
And can connect when I'm in LAN
So it's all the same
…On Wed, Dec 18, 2024, 10:40 Matt Bentley ***@***.***> wrote:
So is that the output of your routes when Tailscale is connected? What
happens if you turn off Tailscale, disable the subnet route setting for
your subnet and reconnect. Are you able to connect to your controller then
with the subnet unchecked?
—
Reply to this email directly, view it on GitHub
<#511 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADFQBZZJYUSI6DHOKXIAKMT2GFGKXAVCNFSM6AAAAABTWBFTMCVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCNRQGM4TIMY>
.
You are receiving this because you authored the thread.Message ID:
<mbentley/docker-omada-controller/repo-discussions/511/comments/11603943@
github.com>
|
Beta Was this translation helpful? Give feedback.
-
|
Wait, so you can connect when you're on the LAN? Sorry, I thought the whole problem was that when you are not able to access your controller when Tailscale is enabled. Is the problem that you're trying to solve that you are not able to connect to the controller when you're connected over the Tailscale network, then? If that is the case, where are you trying to connect from? What network are you trying to connect from when you're trying to connect over the Tailscale network? As in, what is your local IP address you're getting from whatever network you're on when you need to use Tailscale? If your local IP is in the 192.168.0.0/24 subnet range and then you connect to Talescale to your network which is also a 192.168.0.0/24 subnet, it's not going to connect. |
Beta Was this translation helpful? Give feedback.
-
|
When I try to remote in via tailscale
I can access another container in my unraid but not omada
That's the issue
…On Wed, Dec 18, 2024, 11:06 Matt Bentley ***@***.***> wrote:
Wait, so you *can* connect when you're on the LAN? Sorry, I thought the
whole problem was that when you are not able to access your controller when
Tailscale is enabled. Is the problem that you're trying to solve that you
are not able to connect to the controller when you're connected *over*
the Tailscale network, then?
If that is the case, where are you trying to connect from? What network
are you trying to connect from when you're trying to connect *over* the
Tailscale network? As in, what is your local IP address you're getting from
whatever network you're on when you need to use Tailscale? If your local IP
is in the 192.168.0.0/24 subnet range and then you connect to Talescale
to your network which is also a 192.168.0.0/24 subnet, it's not going to
connect.
—
Reply to this email directly, view it on GitHub
<#511 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADFQBZYBDH4B6R2CWHRROVL2GFJL7AVCNFSM6AAAAABTWBFTMCVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCNRQGQZDCNY>
.
You are receiving this because you authored the thread.Message ID:
<mbentley/docker-omada-controller/repo-discussions/511/comments/11604217@
github.com>
|
Beta Was this translation helpful? Give feedback.
-
|
Thanks for clarifying. What about the other info I asked? |
Beta Was this translation helpful? Give feedback.
-
|
What network are you trying to connect from when you're trying to connect
over the Tailscale network?
In this case my job Lan is 172.16 range
But my tailscale IP can be seen in the photos it's 100.xxx.xx
As in, what is your local IP address you're getting from whatever network
you're on when you need to use Tailscale?
It's same range has above
My local IP on tailscale is (on my phone) 100.77.71.56
…On Wed, Dec 18, 2024, 11:15 Matt Bentley ***@***.***> wrote:
Thanks for clarifying. What about the other info I asked?
—
Reply to this email directly, view it on GitHub
<#511 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ADFQBZ4I5OZVBMKYGWH7CWL2GFKNBAVCNFSM6AAAAABTWBFTMCVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCNRQGQZTENQ>
.
You are receiving this because you authored the thread.Message ID:
<mbentley/docker-omada-controller/repo-discussions/511/comments/11604326@
github.com>
|
Beta Was this translation helpful? Give feedback.
-
Controller Version
5.15.6.7
Describe Your Issue or Question
After unraid deployment, cannot access webUI
Expected Behavior
Should able to connect
Steps to Reproduce
How You're Launching the Container
Container Logs
MongoDB Logs
No response
Additional Context
No response
Beta Was this translation helpful? Give feedback.
All reactions